A new version of Cineversity has been launched. This legacy site and its tutorials will remain accessible for a limited transition period

Visit the New Cineversity
 
 
   
 
Choco bar break
 
iacdxb
Posted: 09 February 2020 03:53 AM   [ Ignore ]  
Avatar
Total Posts:  238
Joined  2012-03-02

I am trying to break bar… but not getting any nice similar effect.
- After the make piece separate, did a small sculpting on side…. not good result.
- Break with spline… but spline get smoother even stroke smooth is 0, how to keep spline same as draw..?
Any other nice option to break bar…?

Thanks,
Imran.

File Attachments
bar.c4d.zip  (File Size: 64KB - Downloads: 191)
Profile
 
 
Dr. Sassi
Posted: 09 February 2020 05:12 AM   [ Ignore ]   [ # 1 ]  
Administrator
Avatar
Total Posts:  12043
Joined  2011-03-04

Hi Imran,

How about the detailing inside the Voronoi Fracture?

Project file:
https://www.amazon.com/clouddrive/share/7wT7t6JgGsjrwMc58MkW59ZtRaIm3UtSi3BjcYkGhIo

More information about this:
https://help.maxon.net/us/index.html#OMOGRAPH_FRACTUREVORONOI-ID_FRACTURE_DETAILING_TAB

Please note that there are Selections available from the Voronoi Fracture object.

My best wishes for your project.

 Signature 

Dr. Sassi V. Sassmannshausen Ph.D.
Cinema 4D Mentor since 2004
Maxon Master Trainer, VES, DCS

Photography For C4D Artists: 200 Free Tutorials.
https://www.youtube.com/user/DrSassiLA/playlists

NEW:
NEW: Cineversity [CV4]

Profile
 
 
iacdxb
Posted: 09 February 2020 05:36 AM   [ Ignore ]   [ # 2 ]  
Avatar
Total Posts:  238
Joined  2012-03-02

Thanks for that.

And Sketch Spline, draw without smoothing…?

Thanks.
...

Profile
 
 
iacdxb
Posted: 09 February 2020 05:42 AM   [ Ignore ]   [ # 3 ]  
Avatar
Total Posts:  238
Joined  2012-03-02

and sorry for that…. a screen capture of your file is more helpful for me to understand….!

thanks,
imran.

Profile
 
 
Dr. Sassi
Posted: 09 February 2020 05:54 AM   [ Ignore ]   [ # 4 ]  
Administrator
Avatar
Total Posts:  12043
Joined  2011-03-04

Imran,

The Sketch Path has a parameter: Stroke Smoothing. If that is not sharp enough, perhaps switch the final spline to Linear. Set Blend and Radius parameters smaller than you might have it right now.
An overview of it starting at 03:26 [min: sec]

The path will cut where it detects an edge, or where the path itself has a vertice (even the Spline interpolation points will produce cut details here). If there is no edge and no vertice/point, then no detailed cut in this location will happen.

What part of the provided file is not clear? The glue part, the detailing, how to set up a selection? So I can focus more on the needed parts. Please advice.

Here is a complete series about all main parts.
https://www.cineversity.com/vidplaylist/voronoi_fracture_reference/

Especially:

Detailing
https://www.cineversity.com/vidplaylist/voronoi_fracture_reference/r19_voronoi_fracture_reference_fracturing_enhancements_detailing

Glue
https://www.cineversity.com/vidplaylist/voronoi_fracture_reference/r19_voronoi_fracture_reference_geometry_glue_1_settings

I hope that covers it, as I’m not sure what I could share in a better way.

All the best

 Signature 

Dr. Sassi V. Sassmannshausen Ph.D.
Cinema 4D Mentor since 2004
Maxon Master Trainer, VES, DCS

Photography For C4D Artists: 200 Free Tutorials.
https://www.youtube.com/user/DrSassiLA/playlists

NEW:
NEW: Cineversity [CV4]

Profile
 
 
   
 
 
‹‹ Unwrap a cloth      Weird behavior in cloth tearing ››